Omc 2 3 Liter Marine Engine Apr 10, 2017. #6. i've had a 2.3 ford with the omc drive for awhile now and i agree completely. if i had to pull the engine, i wouldn't put another back in. the merc 4.3 alpha would be my go to. with a hull and interior in the kind of shape you describe, it would be worth converting. Its like pulling a trailer up a mountain pass full time. there are more variables that affect performance hull design, weight is the hull clean and trimmed properly, engine health. then you use wot rpm to determine the prop pitch. my volvo penta 2.3 is also rated at 120hp with a 1 barrel carb and points ignition.
Omc Cobra 2 3 Liter Ford Marine Engine Complete 1990 Youtube 14. jun 5, 2009. #1. i have a 1987 renken 1750 with a 1987 omc cobra 2.3 liter. model# 232amftc. i bought this boat a little while ago and apparently, because of my ignorance, was taken on this purchase. i have done a number of things to this boat an engine already. which i now realize was a very dumb mistake, as i did all these things before. Running on 2 stroke gas with stabilizer for videonow block is drained and cylinders oil foggedwelded manifold not leaking 300$ to change to one not welded. My first start after winter video was mildly popular, so i decided to film the winter preparation of the boat.this video documents how i winterized an omc 2 . Stougaard said: it is a brand new impeller thats in it, and i am getting a pee stream. remove water pump cover from lower unit. start the boat on muffs. you should see a pee stream from the impeller cover vent hole. also, check the gasket on impeller cover to see if it came out of the groove. if it did the pump will suck air causing an overheat.
Omc 2 3 Liter Marine Engine My first start after winter video was mildly popular, so i decided to film the winter preparation of the boat.this video documents how i winterized an omc 2 . Stougaard said: it is a brand new impeller thats in it, and i am getting a pee stream. remove water pump cover from lower unit. start the boat on muffs. you should see a pee stream from the impeller cover vent hole. also, check the gasket on impeller cover to see if it came out of the groove. if it did the pump will suck air causing an overheat. Re: 2.3 ltr omc ford overheating. take the hose from the transom that goes to the t stat housing (some of these have a power steering or oil cooler in line), remove it from the t stat housing and holding it facing up start the engine and you should have 3 or 4 inches of water coming out, if not then the problem is in the out drive, could be a a. I purchased a pertronix ignitor electronic ignition for my 2.3l omc inboard outboard to replace the points and condenser. looking online before purchase, these seem pretty easy to install but when i received it, there's a note about omc motors with electronic shift assist (esa). there is this electronics you have to piece together.
Buy 1989 Omc 2 3l Model 232bmrmef Motor 985683 Boat Marine Ford Eng Re: 2.3 ltr omc ford overheating. take the hose from the transom that goes to the t stat housing (some of these have a power steering or oil cooler in line), remove it from the t stat housing and holding it facing up start the engine and you should have 3 or 4 inches of water coming out, if not then the problem is in the out drive, could be a a. I purchased a pertronix ignitor electronic ignition for my 2.3l omc inboard outboard to replace the points and condenser. looking online before purchase, these seem pretty easy to install but when i received it, there's a note about omc motors with electronic shift assist (esa). there is this electronics you have to piece together.
Comments are closed.